Bargain HyperX Fury 16GB(2x8GB) 2400MHz DDR4 CL15 DIMM Black Memory Kit Stockists
 

HyperX Fury 16GB(2x8GB) 2400MHz DDR4 CL15 DIMM Black Memory Kit Stockists

HyperX Fury 16GB (2X8GB) DDR4 2133MHz CL14 DIMM Black Memory Kit DESCRIPTION HyperX HX424C15FB2K2/16 is a kit of two 1G x 64-bit (8GB) DDR4-2400 CL15 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 1G x 8-bit FBGA components per module. Each module kit supports Intel Extreme Memory Profiles (Intel XMP) 2.0. Total kit capacity is 16GB. Each module has been tested to run at DDR4-2400 at a low latency timing of 15-15-15 at 1.2V. Additional timing parameters are shown in the Plug-N-Play (PnP) Timing Parameters section below. The JEDEC standard electrical and mechanical specifications are as follows: Note: The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS. JEDEC/XMP TIMING PARAMETERS JEDEC/PnP: DDR4-2400 CL15-15-15 @1.2V DDR4-2133 CL14-14-14 @1.2V XMP Profile #1: DDR4-2400 CL15-15-15 @1.2V SPECIFICATIONS CL(IDD) 15 cycles Row Cycle Time (tRCmin) 46.75ns(min.) Refresh to Active/Refresh Command Time (tRFCmin)  350ns(min.) Row Active Time (tRASmin) 29.125ns(min.) Maximum Operating Power TBD W* UL Rating 94 V - 0 Operating Temperature  0oC to +85oC Storage Temperature -55oC to +100oC *Power will vary depending on the SDRAM used. FEATURES Power Supply: VDD = 1.2V Typical VDDQ = 1.2V Typical VPP - 2.5V Typical VDDSPD = 2.2V to 3.6V Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals Low-power auto self refresh (LPASR) Data bus inversion (DBI) for data bus On-die VREFDQ generation and calibration Single-rank On-board I2 serial presence-detect (SPD) EEPROM 16 internal banks; 4 groups of 4 banks each Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS) Selectable BC4 or BL8 on-the-fly (OTF) Fly-by topology Terminated control command and address bus Height 1.340” (34.04mm), w/o heatsink

Bargain Deal: £129.99

HyperX Fury 16GB(2x8GB) 2400MHz DDR4 CL15 DIMM Black Memory Kit Deals on eBay HyperX Fury 16GB(2x8GB) 2400MHz DDR4 CL15 DIMM Black Memory Kit Deals on Amazon
StockistProductPrice 
EbuyerHyperX Fury 16GB(2x8GB) 2400MHz DDR4 CL15 DIMM Black Memory Kit£129.99Visit Store
 
 

HyperX Fury Series 8GB 1333MHz DDR3 CL9 DIMM (Kit of 2) PC Memory

SPECIFICATIONS CL(IDD) 9 cycles Row Cycle Time (tRCmin) 49.125ns (min.)...

SPECIFICATIONS CL(IDD) 9 cycles Row Cycle Time (tRCmin) 49.125ns (min.) Refresh to Active/Refresh 260ns (min.) Command Time (tRFCmin) Row Active Time (tRASmin) 36ns (min.) Maximum Operating Power TBD W* (per module) UL Rating 94 V - 0 Operating Temperature 0oC to 85o C Storage Temperature -55oC to +100o C *Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 667MHz fCK for 1333Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 9, 8, 7, 6 • Programmable Additive Latency: 0, CL - 2, or CL - 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe...


 
 

HyperX Fury 4GB 1866MHz DDR3 CL10 DIMM Memory

SPECIFICATIONS CL(IDD) 10 cycles Row Cycle Time (tRCmin) 44.75ns (min.)...

SPECIFICATIONS CL(IDD) 10 cycles Row Cycle Time (tRCmin) 44.75ns (min.) Refresh to Active/Refresh 260ns (min.) Command Time (tRFCmin) Row Active Time (tRASmin) 32.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V - 0 Operating Temperature 0oC to 85o C Storage Temperature -55oC to +100o C *Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 933MHz fCK for 1866Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6 • Programmable Additive Latency: 0, CL - 2, or CL - 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data...


 
 

HyperX Fury Red 8GB 1600MHz DDR3 CL10 DIMM (Kit of 2) Memory

SPECIFICATIONS CL(IDD) 10 cycles Row Cycle Time (tRCmin) 48.125ns (min.)...

SPECIFICATIONS CL(IDD) 10 cycles Row Cycle Time (tRCmin) 48.125ns (min.) Refresh to Active/Refresh 260ns (min.) Command Time (tRFCmin) Row Active Time (tRASmin) 37.5ns (min.) Maximum Operating Power TBD W* (per module) UL Rating 94 V - 0 Operating Temperature 0oC to 85o C Storage Temperature -55oC to +100o C *Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 800MHz fCK for 1600Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 11, 10, 9, 8, 7, 6 • Programmable Additive Latency: 0, CL - 2, or CL - 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential...


 
 

HyperX 8GB 1600MHz DDR3 Non-ECC CL9 DIMM (Kit of 2) XMP HyperX Savage

Attack the competition with HyperX Savage memory. Its unique, asymmetrical...

Attack the competition with HyperX Savage memory. Its unique, asymmetrical red heat spreader is made from high-quality aluminum and has a black PCB and a diamond cut finish to make your game shine and help you stand out in the crowd. The heat spreader dissipates heat so your system stays cool and reliable and its low profile fits under oversized CPU coolers. Featuring a design that works well with the latest trends in gaming, HyperX Savage comes in a wide range of high-performance speeds, from 1600MHz to 2400MHz, and capacities from 4GB to 8GB in single modules and 8GB to 32GB kits. In CL9-CL11 latencies, it delivers ultra-responsive multitasking and an overall faster system. Dual and quad channel kits are available. Built-in, hand-tuned XMP profiles let users reach higher-performing frequencies, timings and voltages simply by enabling Intel's XMP tool. Even noobs can overclock their platforms with...


 
 

HyperX Fury Black 16GB (4x4GB Kit) 2400MHz DDR4 Non-ECC CL15 DIMM

Automatic overclocking for X99 platforms. HyperX FURY DDR4 can handle...

Automatic overclocking for X99 platforms. HyperX FURY DDR4 can handle even the toughest battle. It automatically recognizes its host platform and overclocks to the highest frequency published (up to 2666MHz) FURY DDR4 runs at 1.2V, even at 2666MHz, so it stays cooler while you play. You don’t need to alter the voltage to reach higher speeds, which means there’s more power for other hardware in the system. FURY’s sleek, asymmetrical black heat spreader provides enhanced thermal dissipation to help keep your cool and help you stand out from the crowd. It complements Intel’s 6- or 8-core processors for faster video editing, 3D rendering, gaming and AI processing. FURY is affordable and available in kits with capacities up to 64GB in black - Automatic overclocking — up to 2666MHz - Low power consumption at 1.2V - Optimized for Intel’s X99 chipset - Stylish low profile...





Copyright © bargainplace.co.uk Inc. All Rights Reserved.