Comprehensive kit of adaptors and fittings for modern Schrader test-port fuel injection systems. Components fitted with quick coupling system and safety valve to prevent inadvertent discharge of fuel under pressure. High pressure, dual scale gauge with hanging hook and protective bumper. Pressure release valve with drain hose for safe fuel recovery. Supplied in carry-case.
Heavy-duty pressure test kit. Aluminium radiator header tank caps colour coded for ease of use and with quick release fittings. Suitable for wide range of vehicle applications and for locating leaks from: head gasket, header tank, radiator and heater cores, water pump, plugs, hoses and housings. Heavy-duty pump unit features smooth action and easy-to-read scale. Long hose aids gauge use and quick release is fitted with pressure release valve for safe operation. Set supplied with thermometer and packed in rugged carry-case.
Suitable for most petrol engined cars and light commercials. ?57mm Gauge fitted with heavy rubber bumper, 150mm hose and M14/M18 fitting. Scale reads from 0-20bar(0-290psi). Includes 5 adaptors and 2 thread chasers covering 4 plug thread sizes. Supplied in carry-case.
?75mm Gauge fitted with heavy-duty cover. Tests oil pump pressure and also low oil warning devices. Fitted with quick coupling adaptors and 1200mm of hose. Includes 90? coupling adaptor for limited access applications. Supplied in carry-case.
?59mm Gauge fitted with 250mm hose and quick connect. Scale reads from 0-21bar(0-300psi). Includes four extension hoses and seven plug thread adaptors from 10 to 18mm. Suitable for most petrol engined cars and light commercials.
Continuity and polarity tester for 6, 12 and 24Volt systems. Positive/negative polarity indicated by red/green LEDs respectively. Supplied with 1.5mtr cable and shrouded earth clip.
Quick-coupling gauge fitted with ?63mm gauge reading up to 300psi and 20kg/cm?. Kit includes 130mm straight and angled push-on connectors, 400mm flexible extension with 14mm, 18mm and 14mm Deep thread adaptors. Supplied in carry-case.
Locate and isolate ECU signal faults fast. Simply disconnect harness and plug in light to see if component is receiving a signal. Noid and idle air control valve indicator lights test for control signal from ECU. 1.3mtr Fibre optic cable allows light to be viewed from the driver?s seat.
Five pairs of cables, colour-coded red, black, blue, orange, yellow. 1.3mm? Cable with shrouded crocodile clips at each end. Use as extensions to multimeter leads, to bridge suspected open-circuit cables and as temporary wiring.
Professional vacuum/pressure diagnostic tool helps identify a variety of faults on vehicle systems including fuel, ignition, transmission, emission and air conditioning/heating. Set also includes reservoirs, hoses and adaptors for bleeding brake and clutch systems. Features lightweight aluminium body with simple twist function for choice of pressure or vacuum testing. Large easy-to-read gauge.
?60mm Gauge with heavy-duty rubber bumper, 400mm of hose and quick connector. Suitable for testing car and light commercial vehicles with direct or indirect injection. Pressure relief valve allows repeated on-vehicle tests. Includes 90? coupling adaptor for limited access applications. Supplied in carry-case.
Comprehensive kit of adaptors and fittings for modern fuel injection systems. Components fitted with quick coupling system and safety valve to prevent inadvertent discharge of fuel under pressure. High and low pressure gauges for accurate readings. Pressure release valve with drain hose for safe fuel recovery. Supplied in carry-case.
The approved method of testing the water content of brake fluid. Supplied in carry-case with full operating instructions.
Designed to measure return fuel flow on diesel vehicles up to 6 cylinders fitted with common rail injection system. Identifies, worn, blocked or inoperative injectors quickly and easily. Supplied with measurement tubes for short term tests and measurement bottles for long term, more accurate evaluation. Supplied in carry-case.
Lockable storage cabinet for VS2110, VS2111 and VS2112 Fuel Injection Pressure Test Kits. You will always know where the kits are and locking the cabinet also prevents the borrowing of kit parts. Supplied with convenient carry handle and two keys.
?80mm Gauge with protective rubber bumper and hanging hook. Checks for leaks in fuel line, vacuum chokes and heating. Includes long flexible hose and adaptors. Supplied in storage case.
Memory Master attaches to a 12V slave battery and provides power via the cigarette lighter socket to on-board electronics whilst vehicle?s own battery is disconnected. Also provides a quick check of the battery?s condition with a digital voltage display. Supplied with 2mtr cable and crocodile clips.
Min. saddle height: 1120mm. Max. saddle height: 1950mm. High speed lift to gearbox - just lift piston. Foot pedal operation keeps hands free. Spring loaded dead man's safety release control reduces the risk of inadvertent lowering. Highly manoeuvrable on castors.
Features super rocket lift to reduce time and effort. Single foot pedal operation keeps hands free during lifting process. Spring loaded dead man?s control decreases risk of inadvertent lowering. Saddle is reversible allowing a jack pad to be fitted to support items other than transmissions. Castors wheels and side handle for easy manoeuvrable.
Jack features steel chassis with welded castor supports and one-piece hydraulic unit. Fitted with overload valve and finger cover for extra safety. Suitable for the hobby user or as an emergency mobile jack. Includes one-piece pumping handle and carry handle. Minimum/Maximum saddle height: 130/330mm. Maximum chassis height: 140mm. Axle stands are constructed entirely from steel and fold flat for ease of storage. Fitted with double locking safety pin. Minimum/Maximum height: 275/365mm. Maximum capacity: 2ton each, 4ton pair.
Min. saddle height: 130mm. Max. saddle height: 350mm. Chassis length 470mm. Steel chassis with welded castor supports and one-piece hydraulic unit. Fitted with overload valve and finger cover for extra safety. Suitable for the hobby user or as an emergency mobile jack. Includes one-piece pumping handle and carry handle.
Min./Max. saddle height: 170/570mm. Heavy-duty chassis with one piece hydraulic unit. Handle mounted safety release prevents inadvertent lowering of load. Includes large diameter saddle for easier positioning under the jacking point. Fitted with safety overload valve. Fully CE approved for general workshop applications.
Min. saddle height: 125mm. Max. saddle height: 390mm. Chassis length: 550mm. Lightweight heavy-duty construction. Supplied in tough storage case to keep dirty jack away from contents of car boot.
Min. saddle height: 130mm. Max. saddle height: 410mm. Chassis length: 625mm. Heavy-duty one-piece hydraulic unit with overload protection.
Suitable for SuperStart range of starter/chargers.